C / K Series Military M-1008 M-1009 Truck / Blazer A/C System

C / K Series Military M1008 M1009 Truck / Blazer A/C System

1955 - 1957(Later Model Model 55) Complete Chevy Truck A/C System

1955 - 1957 (Later Model 55) Complete Chevy Truck A/C System

1947 - 1955 (Early Model 55) Chevy Truck A/C System with Heat

Availability: In stock
Part Number
CK-4753CHPU
$1,252.24

1947-1955 (early model 1955) Chevy Truck Complete A/C system. This kit will mount on the passenger side of the firewall, it will not interfere with the glove box. The kit requires the removal of the factory heater box from inside the vehicle. The kit has an Under-Dash vent panel that runs from the passenger side to the center of the dash, then has another vent on the driver side of the cab.

The kit is complete and includes the following (Kit contents can vary depending on options picked):

1.)   In Dash Evaporator with A/C, Heat, Defrost, and Floor Heat. Expansion Valve Pre-Installed
2.)   Hardware bag with mounting hardware, Grommets and Drain Tube.
3.)   Under-Dash panel with built in Vents and Control Pod that fits contour of dash.
4.)   R-134a Hose kit (See hose kits Page for contents).
5.)   Black O-ring drier with drier straps.
6.)   14 x 18 Condenser with condenser mount kit.
7.)   Sanden Style A/C compressor with clutch (OEM Sanden available as an upgrade).
8.)   Compressor mount kit (to fit your Small Block or Big Block Chevy engine with V-Belt Pulleys).
9.)   HI / Lo Binary pressure switch.
10.) Directions.

Kit is available with come with either cable controls (Default Option) or you have the option to send us your controls to modify. Several upgrade options are available.

1947-1955 (early model 1955) Chevy Truck Complete A/C system. This kit will mount on the passenger side of the firewall, it will not interfere with the glove box. The kit requires the removal of the factory heater box from inside the vehicle. The kit has an Under-Dash vent panel that runs from the passenger side to the center of the dash, then has another vent on the driver side of the cab.

The kit is complete and includes the following (Kit contents can vary depending on options picked):

1.)   In Dash Evaporator with A/C, Heat, Defrost, and Floor Heat. Expansion Valve Pre-Installed
2.)   Hardware bag with mounting hardware, Grommets and Drain Tube.
3.)   Under-Dash panel with built in Vents and Control Pod that fits contour of dash.
4.)   R-134a Hose kit (See hose kits Page for contents).
5.)   Black O-ring drier with drier straps.
6.)   14 x 18 Condenser with condenser mount kit.
7.)   Sanden Style A/C compressor with clutch (OEM Sanden available as an upgrade).
8.)   Compressor mount kit (to fit your Small Block or Big Block Chevy engine with V-Belt Pulleys).
9.)   HI / Lo Binary pressure switch.
10.) Directions.

Kit is available with come with either cable controls (Default Option) or you have the option to send us your controls to modify. Several upgrade options are available.

If you need a different size condenser please specify the size in the checkout section. The compressor will come with a double V-belt clutch unless a different setup is requested. Pulleys and a radiator fan are not included. A fan and fan shroud should be used on the radiator, or a sufficient electric fan. The setup requires a double groove water pump pulley, and a triple groove crank pulley. Please specify in checkout if you have a long or short water pump and if the alternator is on the driver or passenger side. A short water pump will sit up against the timing chain cover; a long water pump will have a one inch gap between the rear of the pump and the timing chain cover. The kit does not include the refrigerant, heater hoses, or belt. This kit is available in 12 volt only.

More Information
Years Covered 1947, 1948, 1949, 1950, 1951, 1952, 1953, 1954, 1955
Make Chevrolet
Model Pickup
Instructions 47-55 Chevy Pickup Kit Instructions
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account