Complete heat air and defrost In-Dash kit that fits into the early fords without interfering with the dashboard, or passenger foot area. The evaporator unit will hide behind the dash with very little of the unit showing. The system uses three vent louvers that can be installed under the dashboard, or cut into the dash. See our vents to choose which style you prefer. The kit includes a condenser that will sit vertically in front of the radiator, and a compressor bracket that sits high on the engine to avoid interfering with the fenders. The system is designed to work with R-134a refrigerant.
The kit includes:
- ID-260 heat air and defrost evaporator (19″ wide x 7-1/2″ deep x 9″ tall).
- Sanden style compressor with clutch assembly and oil
- 19″ tall x 12″ wide Superflow condenser with mounting brackets
- Cables, and controls to use the original heater control panel
- Standard O-ring drier with mounting strap
- High low pressure switch
- Compressor bracket (to fit your specific engine setup)
- R-134a hose kit with fittings (see kit contents)
- Three dash vents, and duct hose (your choice of vents)
- Expansion valve, heater control valve
- All mounting hardware
- Directions
This kit is designed to fit a small block Chevy engine. The kit has the option of defrost, if you do not want the defrost option please let us know in the comment section during checkout. Please let us know your vent choice in the comment section at checkout.
The Compressor will come with a double V-belt clutch unless a different setup is requested. Pulleys and a radiator fan are not included. A fan and fan shroud should be used on the radiator, or a sufficient electric fan. The setup requires a double groove water pump pulley, and a triple groove crank pulley. Please specify in checkout if you have a long or short water pump and if the alternator is on the driver or passenger side. A short water pump will sit up against the timing chain cover; a long water pump will have a one inch gap between the rear of the pump and the timing chain cover. Heater hose, belt, and refrigerant are not included.
1932-1936 Ford AC & Heat Kit Chevy Engine
Complete heat air and defrost In-Dash kit that fits into the early fords without interfering with the dashboard, or passenger foot area. The evaporator unit will hide behind the dash with very little of the unit showing. The system uses three vent louvers that can be installed under the dashboard, or cut into the dash.
Several upgrade options are available for this kit using the options below.
Please specify your engine below if you have a different engine that is not a Small Block or Big Block Chevy with a V-Belt Setup.
$1,312.11 – $1,917.11
Complete heat air and defrost In-Dash kit that fits into the early fords without interfering with the dashboard, or passenger foot area. The evaporator unit will hide behind the dash with very little of the unit showing. The system uses three vent louvers that can be installed under the dashboard, or cut into the dash. See our vents to choose which style you prefer. The kit includes a condenser that will sit vertically in front of the radiator, and a compressor bracket that sits high on the engine to avoid interfering with the fenders. The system is designed to work with R-134a refrigerant.
The kit includes:
This kit is designed to fit a small block Chevy engine. The kit has the option of defrost, if you do not want the defrost option please let us know in the comment section during checkout. Please let us know your vent choice in the comment section at checkout.
The Compressor will come with a double V-belt clutch unless a different setup is requested. Pulleys and a radiator fan are not included. A fan and fan shroud should be used on the radiator, or a sufficient electric fan. The setup requires a double groove water pump pulley, and a triple groove crank pulley. Please specify in checkout if you have a long or short water pump and if the alternator is on the driver or passenger side. A short water pump will sit up against the timing chain cover; a long water pump will have a one inch gap between the rear of the pump and the timing chain cover. Heater hose, belt, and refrigerant are not included.
Additional information
235 6cyl 1947-1954, 235 6cyl 1955-1962, 348-409 W Series Alternator Drivers Side, 348-409 W Series Alternator Passenger Side, Big Block Chevy, Long Water Pump, Alternator Drivers Side, Big Block Chevy, Long Water Pump, Alternator Passenger Side, Big Block Chevy, Short Water Pump, Alternator Drivers Side, Big Block Chevy, Short Water Pump, Alternator Passenger Side, Engine not listed. (Specify Engine information in comments. Extra charges may apply), LS Engine (Specify Year and Model of vehicle engine came out of. Extra charges may apply, LT Engine 2nd Gen (Specify Year and Model of vehicle engine came out of. Extra charges may apply, Serpentine Setup (Specify Engine information in comments. Extra charges may apply), Small Block Chevy, Long Water Pump, Alternator Drivers Side, Small Block Chevy, Long Water Pump, Alternator Passenger Side, Small Block Chevy, Short Water Pump, Alternator Drivers Side, Small Block Chevy, Short Water Pump, Alternator Passenger Side
Advertised Compressor, Chrome Compressor, No Compressor, No Bracket, OEM Sanden 508 (Made in Singapore), OEM Sanden 709 (Made in USA)
Advertised Controls, Factory Controls (Send your controls to us)
Chrome Drier with Bracket (Attached to Condenser), Chrome Drier with Bracket (Not Attached to Condenser), No, Yes Painted, Yes Unpainted
Ford
Car, Pickup
1932-1936
Related products
Complete Triumph TR6 A/C System
SKU: CK-2110 $1,419.73Ford Indash AC Heat Defrost Kit 1951-1985
SKU: CK-5185IFD1964 – 1967 Mustang A/C Kit 170 – 200 Ci Six Cylinder
SKU: CK-6467-1 $1,052.24 – $1,447.24Complete A/C System MGB Chrome Bumper V-Belt
SKU: CK-2101 $1,367.74